|
|
| 啊啾哇MP118TH-C其它 |
 |
產品簡介
額定電流: 1A-5A 品牌: AUQAV
型號: MP118TH-C 產品型號: MP118TH-C
產品報價：130元 |
|
| 啊啾哇MP118TH-C其它詳細介紹 |
1. Power Supply Overview 電性能指標:
1.1 Table 1 Input Electrical Characteristics Overview（輸入特性）
| Input voltage range 輸入電壓 |
90Vac to 264Vac |
| Normal voltage range 標稱輸入 |
100Vac to 240Vac |
| Frequency range 頻率范圍 |
50Hz/60Hz±5% |
Max input ac current
滿載輸入電流 |
2.6Amax at full load and 90Vac condition |
Inrush current (cold start)
浪涌電流 |
50Atyp peak, 120Vac; 100Atyp peak, 220Vac |
| Efficiency(full load) 效率 |
82%min at 90Vac; 86%min at 220Vac Typ. |
| Harmonic current 諧波電流 |
Meet GB17625.1-2003/IEC61000-3-2 class D |
| Leakage Current 泄漏電流 |
Less Than 0.5mA at 240Vac input |
| Standby Power Loss 待機功耗 |
≦0.5W 240Vac input at 5Vsb Output current≤10mA |
| Input Fuse 輸入保險 |
T5AH/250Vac |
1.2 Output Electrical Characteristics Overview（輸出特性）
1.2.1 Table 2 Output Voltage ,Current & Regulation.（輸出調整率）
Output Voltage
輸出電壓 |
Regulation
調整率 |
Min. current
最小電流 |
Load current range
帶載電流范圍 |
Peak current or power
峰值電流或功率 |
| +V1(+24V) |
+V1±5% |
0.2 A |
0.2A-5A |
≤190W |
| +V2(+12V) |
+V2±5% |
0.3 A |
0.3A-3.5A |
| +5.0V |
+5.2V±2% |
0.1 A |
0.1A-1.5A |
≤15W |
| +5.0V(SB) |
+5.2V±2% |
0.01 A |
0.01A-1A |
Note:* The peak current or power should be test at other of dc output at Rated
load ,And the peak current pulse width within 100ms 峰值電流或功率的測試是在其它額定
負載時測試，且脈寬小于100 毫秒。
1.2.2 Table 3 DC Output Ripple & Noise. （輸出紋波和噪聲）
| Output Voltage |
Ripple & Noise (Max.) |
| +V1(+24V) |
240mVp-p@25℃; 350mVp-p@-10℃ |
| +V2(+12V) |
120mVp-p@25℃; 200mVp-p@-10℃ |
| +5.0V |
50mVp-p@25℃; 150mVp-p@-10℃; |
| +5.0V(SB) |
60mVp-p@25℃; 200mVp-p@-10℃; 150mVpp when STB |
Note: 1) Measurements shall be made with an oscilloscope with 20MHz bandwidth.
示波器須設置在20 兆赫茲帶寬
2) Outputs shall be bypassed at the connector with a 0.1uF ceramic capacitor and a
10uF electrolytic capacitor to simulate system loading.
輸出須并聯0.1uF 的陶瓷電容和10uF 的電解電容來模擬負載.
1.2.3 Output Transient Response. （輸出動態響應）
Table 4. Test condition.測試條件
| Voltage Tolerance Limit |
Slew Rate |
Load Change |
5.0V/5.0VS±5%
24V/12V/±10% |
0.2A/u S |
Min. to 50% load and 50% to Max load |
| All output±10% |
0.2A/u S |
Min. load to Max load | Note: Transient response measurements shall be made with a load changing repetition
rate of 50Hz to 10kHz. 以50~10KHz 的頻率跳變負載來測試。
1.2.4 Table 5 DC Output Hold-Up Time. （輸出保持時間）
| Output Voltage |
120Vac input |
220Vac input |
| +V1(+24V) |
≥10 m S |
≥10 m S |
| +V2(+12V) |
≥10 m S |
≥10 m S |
| +5.0V |
≥10 m S |
≥10 m S |
| +5.0V(STB) |
≥10 m S |
≥10 m S | Note: All of dc output at full load. 所有輸出帶滿載
1.2.5 Table 6 DC Output Overshoot At Turn On & Turn Off.（輸出超調）
| Output Channel |
Output(V) |
Over shoot voltage(V)超調電壓 |
| Turn on 開機 |
Turn off 關機 |
| +V1(+24V) |
+ 24V |
10% |
10% |
| +V2(+12V) |
+ 12V |
10% |
10% |
| +5.0V |
+5.0V |
10% |
10% |
| +5.0V(SB) |
+5.0V |
10% |
10% | Note: All of dc output current from Min. to Max. 測試時負載范圍：最小到最大
1.2.6 Table 7 DC output voltage rise time（輸出上升時間）
| Output Voltage |
120Vac input &Full Load |
220Vac input &Full Load |
| +V1(+24V) |
≤100mS |
≤100mS |
| +V2(+12V) |
≤100mS |
≤100mS |
| +5.0V |
≤100mS |
≤100mS |
| +5.0V(SB) |
≤50mS |
≤50mS |
Note: The output voltages shall rise from 10% to 90% of their output voltage.
輸出從10%上升到90%的時間
1.3 Remote On/Off Control：（遙控功能）
The power supply DC outputs (without +5.0Vsb) shall be enable with an active-high TTL(≥2.5V/2.0mA)-compatible signal(Ps-on). The +5.0Vsb is on whenever the AC power is present.
除5.0Vsb 外，其余輸出受控于一個TTL 電平兼容的信號（Ps-on≥2.5V/2.0mA）,
5.0Vsb 上電就存在。
* When Ps-on is pulled to TTL high, the DC outputs are to be enabled.Ps-on 高電平，打開輸出.
* When Ps-on is pulled to TTL low or open circuit, the DC outputs are to be disabled.Ps-on 低電平，關閉輸出.
Table 8.
| Ps-on Signal |
Comments |
Outputs |
| Ps-on- high |
≥2.5V&2.0mA ( source) |
Output |
| Ps-on- low |
≤ 0.5V |
X |
| Ps-on-open |
-- |
X |
1.4 Protection: （保護功能）
1.4.1 Table 9 DC output Over Voltage Protection. （輸出過壓保護）
| Output Voltage |
TYP. Over Voltage |
Comments |
| +V1(+24V) |
27V |
Power supply latch into shutdown state
輸出鎖機 |
| +V2(+12V) |
14V |
Power supply latch into shutdown state
輸出鎖機 |
Note: The power supply shall be test at max AC voltage (264Vac) and min load or no load.
應該在最大交流輸入電壓264 伏和輕載、空載下測試。
1.4.2 Table 10 DC Output Over current Protection. （輸出過流保護）
| Output Voltage |
Over Current |
Comments |
| +V1(+24V) |
≥6Atyp* |
Hiccup嘗試重復啟動 |
| +V2(+12V) |
≥5Atyp* |
Hiccup嘗試重復啟動 |
| +5V |
≥2Atyp* |
Hiccup嘗試重復啟動 |
| +5.0VSB |
≥1.5Atyp* |
Hiccup嘗試重復啟動 |
Note:* The over current protection should be test at other of dc output at Rated load but the 24V over current protection should be test at 12Vdc output at min load.5V 和5VSTB 過流保護測試是在其它額定負載時測試.而24V 過流測試是在12V 輕載電流時測試。
1.4.3 Table 11 DC Output Short Circuit Protection. （輸出短路保護）
| Output Voltage |
Comments |
| +V1(+24V) |
Shutdown關機 |
| +V2(+12V) |
Shutdown 關機* |
| +5V |
Hiccup 嘗試重復啟動 |
| +5.0V(SB) |
Hiccup 嘗試重復啟動 |
Note:* The Short Circuit protection should be test at other of dc output at Rated load
短路保護測試是在其它額定負載時測試.
1.4.4 Re set After Shutdown.（保護功能復位）
Recycle the ps-on signal, the power supply will restart after the fault removed，But +5V、+5.0V(STB)output over voltage can’t be re set .
故障去除后，關掉Ps-on 信號再打開，電源即可恢復。+5V、+5.0V(STB)過壓后不可恢復。
2. Isolation（絕緣性能）
2.1 Table 12 （絕緣阻抗）
| Input To Output |
DC500V 50MΩmin (at room temperature) |
| Input To FG |
DC500V 50MΩmin (at room temperature) |
| Output To FG |
Non Isolated | 2.2 Table 13 （絕緣耐壓）
| Input To Output |
3000Vac 50Hz 1minute ≤10mA |
| Input To FG |
1500Vac 50Hz 1minute ≤10mA |
| Output To FG |
Non Isolated | Note: Open FG and Output return. 交流地和輸出負極要斷開。
3. Safety （安全規格）
The power supply shall compliance with the following Criterion:
電源安全性滿足下列標準
1) UL60065
2) EN60065
3) GB8898-2001
4. EMC （電磁兼容性）
4.1 EMI （電磁干擾）
The power supply shall compliance with the following Criterion:
電源電磁干擾滿足下列規則：
1) Conduction Emission : （傳導干擾度）
*EN55013, CLASS B
*GB13837, CLASS B
*FCC PART15 CLASS B
2) Radiated Emission : （輻射干擾度）
*EN55013, CLASS B
*GB13837, CLASS B
*FCC PART15 CLASS B
4.2 EMS （電磁抗擾）
The power supply shall compliance with the following Criterion:
電源電磁抗擾滿足下列規則：
1) ESD （靜電抗擾度）
*GB17626.2-1998/IEC61000-4-2
2) EFT （脈沖群抗擾度）
*GB17626.4-1998/IEC61000-4-4 3KV
3) Surge （雷擊浪涌）
*GB17626.5-1998/IEC61000-4-5 1.5KV / 3KV
5. Environmental Requirement （工作環境）
5.1 Temperature （環境溫度）
* Operating: 0℃ to +40℃.
* Store: -20℃ to +80℃.
5.2 Humidity （環境濕度）
* Operating: from 10%to90% relative humidity (non-condensing).
* Store: from 5 to 95% relative humidity (non-condensing).
5.3 Altitude （海拔高度）
* Operating: to10,000 ft.
* Store: to 20,000ft.
5.4 Cooling Method （冷卻方式）
* Ventilation cooling . 自然冷卻
5.5 Vibration （振動耐受）
* 10-55Hz, 19.6m/s2(2G), 3minutes period, 60minutes each along X, Y and Z axis.
5.6 Impact （沖擊耐受）
* 49m/s2(5G),11ms, once each X, Y and Z axis.
6. Dimension （物理尺寸）
* 180mm × 180mm ×11mm (長L *寬W * 高H ).板面高
7. Weight （重量）
* 約500g
8. Pin Connection (連接器腳位定義)
Table 15 Pin-CON4 Connection And Function
|
|
